How to Fix Water Hammer?

fixing water hammer

What causes water hammer? | Where to install a check valve for water hammering? | Is water hammer common? | How much does it cost to fix a water hammer in Australia? | How to stop water hammer? | What are water hammer arrestors? | What is a common water hammer problem? | Does water hammer affect your washing machine? | Does water hammer affect plumbing pipes?

Water hammer results when the water pressure decreases rapidly. It’s not a serious problem and can be fixed by turning off the tap more slowly. Often the problem can be resolved by installing a check valve. A check valve allows water flow in one direction only, so when the pressure at one end of the pipe drops rapidly (as it does under certain conditions), there is no back-flow to cause problems.

Check valves are inexpensive and easy to install. It’s also possible to install or re-install air chambers, accumulators and expansion tanks that can help prevent a water hammer as well.

What Causes Water Hammer?

Water hammer results when the water pressure decreases rapidly. There are a number of things that can cause this sudden decrease in pressure, including shutting off the water supply at the end of a long hose, changing to a lower-pressure faucet (or opening a faucet already open), and removing plugs from plumbing fixtures.

This type of problem is not an emergency, but fixing it can be as simple as just turning off the tap more slowly and installing a check valve.

Where to Install a Check Valve for Water Hammering?

Check valves can be installed on hot and cold water supply lines (even in pipes under the floor or behind walls). Most plumbers will recommend installing check valves on both hot and cold water supply lines where damage could occur. If your home is connected to a well with an air chamber, you might not need more than one check valve. But make sure that if there is already a check valve installed, it’s working properly first; before installing another one. Make sure any check valve you install is designed for indoor plumbing use: They’re made of plastic or brass. Brass ones are more durable, but they cost more too.

Is Water Hammer Common?

Water hammer is not common because it occurs when the water’s pressure decreases rapidly. There are a number of things that can cause this sudden decrease in pressure, including shutting off the water supply at the end of a long hose, changing to a lower-pressure faucet (or opening a faucet already open), and removing plugs from plumbing fixtures. It is not an emergency and can be fixed by turning off the tap more slowly or by installing a check valve.

How Much Does It Cost to Fix a Water Hammer in Australia?

The water hammer can be easily fixed by turning off the tap more slowly or by installing a check valve. A plumber charges $95-$130 an hour and will charge between $80-$150 for the installation of a check valve, depending on where it’s installed (it’s easier to install under sinks).

Having a plumber install an air chamber, expansion tank or accumulator costs between $200-$500 for the labour, depending on several factors, but getting an individual quote from an Australian plumber is the best way to determine the price for your situation.

How to Stop Water Hammer?

fixing water hammer

Water hammer can be stopped by installing a pressure reducing valve or an anti-surge valve. Both of them will control the flow of water supply entering into the pipeline by maintaining a minimum level pressure in the pipeline.

Here are some explanations on how a pressure reducing valve and an anti-surge valve is installed:

Pressure Reducing Valve (PRV) A PRV will reduce the incoming water level to a predetermined level, which means it stops delivering any more water when its preset limit was reached. It sounds like a very simple device, but based on different parameters like flow rate and house pressure, you may need to have several sizes of valves for your home or business purposes. The ability of the PRV to stop or slow down water flow depends greatly on how much head drop. For example, the difference in water levels between the incoming water line and the appliance is created.

A PRV is connected to a flexible Hose Bibb which allows you to connect it directly into an aperture without any additional piping work needed. That means once installed, you can neither remove nor replace this valve with another size. So make sure that you ask for some help from a professional plumber before installing one of these things at home or business place. The device comes in different sizes, but most manufacturers offer mid-size regulators basically suitable for anything from 5/8 inch pipe diameter up to 3/4 inch pipe diameter (3/4 inches being the maximum standard PVC plumbing size). Most retail stores sell them as their main product so each time when I need a pressure regulator, I visit my local Home Depot store and get one. You can save a lot of money by doing that way. In my case, when the valve was installed at home, it costs only about $15 for each regulator.

The anti-surge valve on the other hand is bigger in size and more expensive in comparison to pressure reducing valves because they work differently than the latter (in terms of their features). Anti-surge valves maintain a minimum flow rate in your water supply or heating system so as to avoid unwanted interruptions caused by air bubbles and sediments within hot water lines. They are used mostly in commercial buildings like restaurants or schools which runs on a high volume water supply with a regular usage pattern (hot water must be always available).

What are Water Hammer Arrestors?

Water hammer arrestors are a device that is installed on the outlet of a water-using appliance to prevent the rapid fluctuations in pressure from causing damage. Water hammer arrestors are easily confused with surge arresters or pressure regulators, as they perform similar functions and all can be installed together on an individual fixture or circuit.

Restrictions: The user must always follow the guidelines specified by the manufacturer of the device while installing it.

Basic function: Improves flow characteristics, which improves system efficiency and reduces noise. Reduces peak flow velocity, thus reducing erosion potential during valve closing (or opening).

Principal cause of damage: A sudden change in water pressure caused by shutting off (or turning on) a water valve at too high a rate causes a shockwave to be sent through the water system, damaging both the fixture and piping.

Water hammer arrestors are designed so that they reduce pressure changes above a certain threshold. They do not eliminate pressure change, but rather reduce them to levels that will not cause damage or erosion of metal surfaces.

Over time this erosion can lead to cracks in the lines, which can potentially leak dangerous contaminants into your water supply (if you live in an area where contamination is a concern).

Signs: The most obvious sign of a problem is often noise coming from your plumbing fixtures so it may be wise to check for these if you think something might be wrong.

What is a Common Water Hammer Problem?

A common water hammer problem is water hammer that results from too much pressure loss in the plumbing system. The plumbing design must account for the water hammer, and a sufficient amount of pressure reduction must be provided so that excessive water hammer does not occur.

Water hammer may have an impact on the piping system when a sudden change in static (or flowing) pressure causes a rapid change in fluid velocity. Water hammer is often caused by valves shutting off quickly, or when using pumps which are usually slower than instantaneous valve closure speeds.

Does Water Hammer Affect Your Washing Machine?

Water Hammer affects a washing machine in the following ways:

1. It causes the washing machine’s top cover to open slightly which lets water come out partially when your washing machine is draining. This not only wastes water but also decreases your monthly water bill.

2. In some cases, it may damage the gasket that separates the cover from the drum of the washing machine causing a leak in your washer.

3. Water hammer can cause your Washing Machine agitator assembly to break because of vibration and shock during each cycle. The washing would be unbalanced, have excessive noise and won’t wash properly until you fix or replace the broken agitator assembly.

Does Water Hammer Affect Plumbing Pipes?

There is a possibility that water hammer affects the functioning of plumbing systems and it should be prevented where possible. Water hammer can happen when there is a change in pressure or flow rate in the system, resulting in an abrupt stop which causes a shock wave from one end to another end of the pipe. It has been found that water hammers can cause severe damage in pipes such as bursting or cracking of joints, machining off threads due to motion, instability etc. This may lead to leakage of fluid, deterioration of performance and complete failure of the piping systems which can result in even more serious problems.

Related Plumbing Resources

Plumbing Quotes

A plumber is a dedicated expert hired to repair and maintain all elements of the water supply including pipes, fittings, and apparatus. Read more…


Plumber Call Out Fee

One of those tradies that are vital to so many aspects of your house is a plumber. It might be routine maintenance, a major renovation project, or an emergency that simply cannot wait. Read more…


What is a Tradie

A skilled manual worker in a specific trade or craft is known as a “Tradie” (trade specialist). Read more…

Air Conditioning

What is a Soakwell?

Soakwells consist of a pot or container filled with a porous material such as perforated pipe, allowing rainfall to soak into the soil. Read more…